收藏本站
SLUU150 – February 2003
1.2
2
2.1
Description
The TPS2390 and TPS2391 simple – 48-V hot swap controllers are integrated solutions
optimized for use in nominal – 48-V systems. They are used in conjunction with an external
N-channel MOSFET and sense resistor to enable hot swap, the insertion and removal of plug-in
cards or modules in powered systems. Both devices feature inrush current slew rate and peak
magnitude limiting, which are easily programmed by the sense resistor value, and a single
external capacitor. They facilitate implementation of platform control of the electrical connection
or isolation of the protected load, and provide single-line load fault reporting. An on-chip timer,
also set by a single capacitor, provides filtering against nuisance breaker trips. These features
are all incorporated into a tiny 8-pin MSOP package.
The TPS2390 latches off in response to current faults. The TPS2391 periodically retries the
load, to test for the continued existence of a fault.
The Simple – 48-V Hot Swap Controller EVM
Module Description
The – 48-V hot swap EVM contains all the components needed to implement a complete telecom
hot swap interface. In addition, it contains some additional components and PCB patterns to
facilitate evaluation of the device.
Banana jacks are provided for connection of the user ’ s power supply. On the switched side of
the hot swap circuit, jacks are also provided for connection of the user ’ s electronic or resistive
load, if desired. The board also contains two through-hole patterns for the installation of
large-value aluminum electrolytic capacitors. This capacitance is used to simulate the input bulk
capacitance present at a plug-in ’ s power inputs. The EVM is supplied from the factory with a
100- μ F capacitor installed in one of the locations. The second pattern, connected in parallel with
the first, can be used to increase or otherwise modify the amount of load capacitance.
From the input power jacks, power is applied to the hot swap circuit via a toggle switch
connected in-line with the high-side of the power bus. Bounce of the switch contacts helps the
user observe the response of the devices under power-up conditions resembling those of an
actual application. An on-board slide switch is also provided to independently toggle the status
of the device enable input (EN pin).
With the TPS2390 and TPS2391, both inrush slew rate limiting and a fault time-out period are
externally programmable using capacitors. On the EVM, several options are provided for slew
rate limiting, for quick comparison of the effect of capacitor value on this function. The capacitors
can be quickly switched in and out of the circuit via the DIP switch. Fault timing programming is
set up in a similar manner; some amount of capacitance is hard-wired into the circuit, with the
option of switching in additional capacitance.
Test points are provided throughout the circuit for easy voltage monitoring via oscilloscope or
voltmeter. The test point connections are listed in Table 4.
A pictorial of the simple – 48 – V hot swap EVM is shown in Figure 1.
Evaluation Modules for Simple – 48-V Hot Swap Controllers
5
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
TR2/1025FA2-R FUSE 2A 125V FAST SMD 1025
TR2/6125FA750MA FUSE BRICK 750MA 125V FST 6125FA
TR2/C515-800-R FUSE 250V .800A T-LAG AXL T/R
TRF250-080T POLYSWITCH PTC RESET 0.08A HOLD
TRF250-080U-2 POLYSWITCH PTC RESET 0.08A T/R
TRF250-110U-2 POLYSWITCH PTC RESET 0.11A HOLD
TRF250-120T-2 POLYSWITCH PTC RESET .12A T/R
TRF250-120T-B-0.5 POLYSWITCH PTC RESET .12A HOLD
相关代理商/技术参数
TPS2392EVM 功能描述:电源管理IC开发工具 Simple -48V Hot Swap Contr EVM RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
TPS2392PW 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2392PWG4 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2392PWR 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2392PWRG4 功能描述:热插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2393APW 功能描述:热插拔功率分布 48V Hot Swap RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2393APWG4 功能描述:热插拔功率分布 -48V Hot Swap RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
TPS2393APWR 功能描述:热插拔功率分布 -48V Hot Swap RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube